2021 Makino F5
Used · CNC Vertical Machining Centers (VMC)
CNC Vertical Machining Centers (VMC)
Makino F5
22 Makino F5 listings have come through the used market we track on 8 marketplaces, built from 2010 to 2021 where the listing gave a year. Listings that repeat the same machine are shown once, as 16 machines.
20,000 RPMSpindle speed
19.7 inY-axis travel
17.7 inZ-axis travel
30Tool capacity
What the maker publishes about the current Makino F5
Makino's F5 is a vertical machining center with X, Y and Z axes, laid out without overhangs on large castings. Travels are 35.4" in X, 19.7" in Y and 17.7" in Z. The table is 39.4" x 19.7", the largest workpiece is 39.4" long, 19.7" wide and 17.7" tall, and table load capacity is 2,204 pounds. The axes use fine pitch ball screws of 8 mm, with scale feedback of 0.05 micron as standard equipment. The spindle is a two-range design that reaches 20,000 rpm and mounts an HSK-63A taper. Its temperature control system uses core cooling, under-race and jacket methods. The lower range serves roughing, while the higher range is used with small tools on fine features. The tool changer is a 30-tool magazine, and a 60-tool magazine is an option.
Source: Makino, October 14, 2026.
Makino F5 specifications
Manufacturer specification. Every figure below was read from the manufacturer’s own published specification for this machine and checked back against that document word for word.
These are the manufacturer’s figures for this model as currently published. A machine built years ago may differ in control generation and in options, which is exactly why the questions below matter when you sell one.
Capacity and travels
X-axis travelX axis travel
35.4"
Y-axis travelY axis travel
19.7"
Z-axis travelZ axis travel
17.7"
Spindle and speed
Max spindle speedspindle
20,000 rpm
Spindle taperspindle
HSK-63A
Table, turret and tools
Table sizetable
39.4" x 19.7"
Max table loadtable load capacity
2,204 pounds
Tool capacitymagazine
30-tool magazine
Further figures the manufacturer publishes
maximum workpiece size
39.4" long x 19.7" wide x 17.7" tall
optional magazine
60-tool magazine (optional)
ball screws
8 mm fine pitch ball screws
scale feedback
0.05 micron
- manufacturer specification page, fetched October 14, 2026.
What fits a Makino F5
Each of these follows from a published specification above, which is named beside it.
HSK-A63 tooling
This machine takes HSK-A63 tooling — a hollow-shank interface, not a 7:24 steep taper. CAT, BT and SK holders do not fit it, and HSK holders of a different size do not fit each other.
Derived from Spindle taper: HSK-63A
What to check on a Makino F5
- Spindle. The manufacturer gives a spindle speed of 20,000 rpm. Run the spindle to top speed and listen for bearing noise.
- Axes and way covers. The manufacturer gives X 35.4", Y 19.7" and Z 17.7" of travel. Run each axis end to end and check the way covers.
- Tool changer. The manufacturer gives the tool capacity as 30-tool magazine. Cycle every pocket and watch for a hesitation.
Makino F5 listing history
Where it was listed
surplusrecord.com
8 listings, model years 2010 to 2021
exapro.com
3 listings, model year 2013
usedcnc.com
3 listings, model years 2017 to 2019
usedmachinerysales.com
3 listings, model years 2012 to 2014
machinetools.com
2 listings, model year 2015
equipt.com
1 listing, model year 2011
revelationmachinery.com
1 listing, model year 2021
theequipmenthub.com
1 listing, model year 2018
Model years seen
2021 (2 units), 2019 (2 units), 2018 (3 units), 2017 (2 units), 2016, 2015, 2014, 2013 (3 units), 2012 (2 units), 2011 (2 units), 2010 (2 units).
What Makino F5 listings agree on
X-axis travel
35.4 in
Y-axis travel
19.7 in
Z-axis travel
17.7 in
Table size
39.4 x 19.7 in
Spindle speed
20,000 RPM
Spindle power
20 hp
Spindle taper
HSK-A63
Tool capacity
30
Machine weight
16,530 lb
Every Makino F5 we have tracked
2021 Makino F5
Used · CNC Vertical Machining Centers (VMC)
2019 Makino F5
Used · CNC Vertical Machining Centers (VMC) · Listed 2 times (usedcnc.com)
2018 Makino F5
Used · CNC Vertical Machining Centers (VMC) · Listed 2 times (surplusrecord.com)
2018 Makino F5
Used · Metal Cutting
2017 Makino F5
Used · CNC Vertical Machining Centers (VMC) · Listed 2 times (usedcnc.com, surplusrecord.com)
2016 Makino F5
Used · CNC Vertical Machining Centers (VMC)
2015 Makino F5
Used · Metal Cutting
2014 Makino F5
Used · CNC Vertical Machining Centers (VMC)
2013 Makino F5
Used · CNC Vertical Machining Centers (VMC)
2013 Makino F5
Used · Metal Cutting · Listed 2 times (exapro.com)
2012 Makino F5
Used · CNC Vertical Machining Centers (VMC)
2012 Makino F5
Used · CNC Vertical Machining Centers (VMC)
2011 Makino F5
Used · CNC Vertical Machining Centers (VMC) · Listed 2 times (equipt.com, surplusrecord.com)
2010 Makino F5
Used · CNC Vertical Machining Centers (VMC) · Listed 2 times (surplusrecord.com)
1 more listing gave no year.
The Makino F5 among machining centers and mills
Browse all CNC Vertical Machining Centers (VMC), or see every Makino machine we track.
Other CNC Vertical Machining Centers (VMC) models in this directory
Haas VF-3
- Units tracked
- 167
- Years seen
- 1993 to 2024
Haas VF-2
- Units tracked
- 162
- Years seen
- 1992 to 2024
Haas VF-2SS
- Units tracked
- 154
- Years seen
- 2003 to 2025
Have a Makino F5 to sell?
We are the buyer, not a broker. No listing fee, no commission, no waiting for someone else to find a buyer. Quote in 24 to 48 hours, we handle rigging and freight, and we arrange the pickup.